12 Common Fence Installation Mistakes and How to Avoid Them
Most fences that fail early were built with one of these. Every one is easy to avoid at the start and expensive to fix later.

When we are called to repair a fence that is leaning, rotting or falling apart after only a few years, the cause is almost always something that happened on the day it was built. Here are the mistakes we see most, from planning to the last coat of stain.
Planning mistakes
1. Building on a guessed property line
A fence a foot onto the neighbor's land can be ordered removed, at the owner's cost. Find the property pins, or get a survey if they are missing, before you set the first post. Our boundary fence guide explains what Washington law does and does not say.
2. Ignoring height rules and HOA covenants
Front yards usually allow less height than back and side yards, and many HOAs set height, material and color. Check fence height rules by city and your covenants first, not after a complaint.
3. Skipping the 811 call
In Washington, a utility locate is required at least two business days before digging, even for one post hole. It is free. Hitting a gas or power line is not.
Post mistakes
4. Posts too shallow
About a third of the post's length should be in the ground, and gate posts deeper still. A shallow post leans as soon as wind loads a solid privacy fence, and it takes the fence with it.
5. Concrete that traps water
Concrete finished below ground level, or flat against the post, collects rainwater where the wood is most vulnerable. Put gravel under the post for drainage and crown the concrete so water runs away from it. Wet clay changes the approach; see fence posts in clay.
6. The wrong posts
Untreated wood, or cedar posts in wet soil, rot at the ground line within a few years. Use pressure-treated posts rated for ground contact, or galvanized steel posts where the ground stays wet.
7. Posts set by eye
Without a tight string line at the top and bottom, posts wander and the fence snakes. Once the concrete sets, the only fix is to dig them out. See how to align fence panels.
Building mistakes
8. Boards touching the soil
Fence boards that sit in the dirt wick up water and rot from the bottom up. Keep them above the ground on a replaceable kickboard.
9. The wrong fasteners
Plain steel nails and screws react with cedar's natural oils, leaving black streaks and rusting through. Use hot-dip galvanized or stainless steel throughout.
10. Ignoring the slope
Panels forced to sit level on a hill leave triangular gaps under the fence; panels racked too far look crooked. Decide between stepping and racking before the posts go in. Fence racking explains the limits.
11. Treating the gate like part of the fence
A gate hung on an ordinary line post, without a diagonal brace, will sag within a season. Gate posts need to be heavier and deeper, the brace must run from the bottom hinge corner up to the latch side, and the opening needs room for the wood to swell in winter. More in gate installation.
Finishing mistakes
12. Staining at the wrong time, or never
Stain on wet new wood does not soak in; cedar left unfinished goes gray and checks faster. Let new cedar dry for a few weeks, apply a penetrating stain in dry weather, and recoat every three to five years. See fence staining and sealing.
One more: the finished side
Many HOAs, and good-neighbor custom, put the finished side of the fence facing out, toward the neighbor or the street. Agree it before you build.
If your fence already has one of these
Many of these can be fixed without starting over: posts reset, kickboards added, gates rebuilt. Our fence repair page covers what can be saved, and the repair or replace guide helps decide when it cannot. Every fence we build carries a lifetime workmanship warranty against exactly these mistakes. Request a free estimate.
More From the Blog
DIY & How-To
How to Install a Wood Privacy Fence: The Build, Step by Step
Layout, post holes, concrete, rails, boards and gate for a 6-foot cedar privacy fence, with the details that matter in the wet Seattle climate.
DIY & How-To
How to Align Fence Panels: Straight Lines, Even Heights, Clean Slopes
Straight fence panels start with the posts: string lines, exact spacing, cutting to height, stepping or racking on slopes, and fixing a crooked panel.
DIY & How-To
Tools for Installing Fence Posts: The Complete Checklist
Every tool for setting fence posts, from string line and post-hole digger to digging bar, auger and post level, with what to rent and what to buy.
Planning a fence?
Price it in a minute with the calculator, or send a few photos for a free written estimate.