Skip to content
Serving Greater Seattle — Eastside, North End & South Sound Call (206) 629-6006
Vista Fence Free Estimate
DIY & How-To

How to Align Fence Panels: Straight Lines, Even Heights, Clean Slopes

A straight fence is decided before the first panel goes up. It is all in the posts.

Horizontal wood-slat fence between black metal posts, seen straight on above a gravel strip

Fence panels that line up perfectly look simple, but the work happens before any panel is hung. If the posts are straight, plumb, evenly spaced and the right height, the panels fall into place. If not, no amount of adjusting the panels will hide it. Here is how to get it right, for wood panels, stick-built fences and vinyl.

1. Set the end and corner posts first

Everything else is measured from these. Set the post at each end and each corner of the run in concrete, plumb on two faces, and brace it so it cannot move while the concrete sets. Take the time here: every other post copies these.

2. Run two string lines

Stretch a tight mason's line between the end posts near the top, and a second one a few inches above the ground. Set them on the face of the posts where the panels will sit, or offset by a block of wood of the same thickness on every post so the string never touches anything in between. Two strings keep the posts in line at both heights, which also stops them leaning in or out along the run.

3. Space the posts to the panel, not the other way round

With pre-built panels, the spacing must match the panel exactly. Decide whether you are measuring from post center to post center or between the faces, and use one method all the way along. The surest approach is to set one line post, fasten the panel to the end post, and let the panel itself place the next post. Measure, dry-fit, then set. For vinyl, whose rails slide into pre-cut holes in the posts, this is essential: there is almost no room for error.

With a stick-built fence, you have more freedom. Space posts evenly along the run, even if that means slightly less than the maximum, rather than ending with one short bay.

4. Plumb every post on two faces

A post can touch both strings and still lean along the line. Check each one with a post level on two adjacent faces, then brace it before the concrete goes in. Check again after you pour, because posts often shift as the concrete is worked in.

5. Cut to height after the concrete sets

Trying to set every post at exactly the same height in wet concrete rarely works. Set them a little tall, let the concrete cure, then mark a single line across all of them, from a string, a chalk line or a laser level, and cut them to it. Hang panels from a line too, not by measuring up from uneven ground.

6. Decide how to handle the slope

On sloping ground the panels can either step down at each post, staying level with a triangle of open space under the low end, or follow the ground, with rails parallel to the slope and pickets still vertical. Stepped panels need the steps to be equal, so divide the total drop by the number of bays. Following the slope works only with panels made to rack. What is fence racking explains which fences can do it and how steep is too steep.

7. Hang panels from the high end

On a slope, start at the top and work down. Fasten each panel at its top first, check it with a level, then fasten the bottom. Keep the gap between the panel and the ground consistent, using a scrap block as a spacer.

Fixing a panel that is already out of line

  • The panel is high or low: move its brackets. If the post itself is too short, add a block or replace the panel bracket rather than forcing it.
  • The post leans: on a recent fence, the post can sometimes be pushed back and braced if the ground is soft. Otherwise it has to be dug out and reset in fresh concrete. A post in a rotted footing must be replaced.
  • The panel sags in the middle: add a block under the bottom rail or a center support. On wood, a third rail fixes it for good.
  • The whole run wanders: it cannot be adjusted straight. The posts have to be reset to a string.

Resetting leaning posts and rehanging panels is a large part of our fence repair work. If you are building new and want it straight from the start, our crews set every fence to a string line. Price your fence or request a free estimate.

Planning a fence?

Price it in a minute with the calculator, or send a few photos for a free written estimate.

Call Free Estimate